February 2, 2021   |   by admin

Edinson Borda Villcas. Test de Percepcion Visual Frostig Manual. Uploaded by. MARIA Abs Cambios Uploaded by. Patricio Patri. Manual Autorizacion Btp. Manual Autorizacion Btp. Uploaded by. Patricio Patri · PROBMON1-Ser Omni 6- 25 Min (Problemas). Uploaded by. Patricio Patri · Test Psi Co Tec Nico. Manual Autorizacion Btp Descripción: PROGRAMACIONES BTP INFORMÁTICA HONDURAS M Topographie 2-Approfondissement BTP- TSGT.

Author: Tutaxe Mashura
Country: Honduras
Language: English (Spanish)
Genre: Video
Published (Last): 19 June 2016
Pages: 195
PDF File Size: 10.65 Mb
ePub File Size: 15.42 Mb
ISBN: 533-2-14342-475-5
Downloads: 24412
Price: Free* [*Free Regsitration Required]
Uploader: Kasar

Run the turret with power to check for proper functioning. Part Name Part No.

Pragati – BTP Turret Manual

Actuation of the switch is indicated by built in LED light emitting diode. Bolts are approachable through holes in bearing flange Manual para estimar edad ysexo en aves del Parque PDF. Align orientation marks on fixed coupling 3 and sliding coupling 4. All these signals should stop the operation of the machine, and an indication should be available on the control panel regarding the nature of the fault.

Temps Unitaire en btp Documents. Electrical motor wiring diagram. It is however not possible to tighten the nut by hand to its full travel up to shaft shoulder. Now tighten the bolts 15 to clamp indexing gear 13 on the spindle. Tighten bolts 15 with a light force. Published on Mar View Download 1.

Simultaneously it is necessary to ensure that the teeth of drive gear 73 and drum cam gear 8 mesh with orientation marks properly aligned. If in doubt connect 24V DC supply to the turret. Replacement of proximity switch: Operation of Coolant system: Adjustment of rotary encoder.


Pragati – BTP Turret Manual – PDF Free Download

Fitment of tool disc on the turret. It also ensures high repeat positioning accuracy as well as rigidity.

Remove gear 85 after removing circlip 88fig. Clamp back plate to body with the help of bolts and cylindrical pins To link to this article: In such a case, in MDI mode, the control should choose a fixed direction of motor rotation i.

Electric motor Encoder Proximity switch 61 Final assembly Spindle assembly Final assembly 1 1 1 Temps Unitaires Projets Btp Description: Otherwise, the turret will get de-clamped and the proximity switch signal will be lost. Even if turret clamping is not possible at this stage follow the next steps. Coolant flow automatically stops during the indexing movement, as the coolant flange closes the opening of the valve button. Clearance should be within 0.

Refer main manusl drawing fig. Coolant ring as well as coolant flange have provision for angular adjustment. It is therefore, not possible to adjust the angular position of coolant ring by hand. This lift should be inspected by using a dial indicator. Assemble all components as shown in figure Assemble all components as shown in fig Follow the procedure given on page 14 to adjust the uatorizacion in proper position.


Work design is based on skills and unique talentsable to facilitate.

Crank the motor by hand in both directions, and check for the correct indexing movement. Only a small possibility of requiring replacement. Coupling design allows maanual tool disc to be indexed without lifting.

Manual Autorizacion Btp

Three piece face gear coupling is the basic element used autorizaccion indexing. Electrical wiring should be brought in through water proof conduit connection. Faults and corrective actions: Clamp the encoder in position,such that the orientation marks on encoder and flange match.

If clearance is low, it should be adjusted by surface grinding the bottom face of cam flange Turret is lubricated by medium viscosity gear box oil. Use extraction screws and pull out the end plate If in two pieces, ensure that the assembly confirms to the side view shown in the figure.

Manual Autorizacion Btp – Editorial Tráfico Vial – Google Books

Adjustment of Ringfeder Clamps 26 In such a case, tool position number, and encoder feedback will not match. Turret Demolition Scope 1Full description. Clamping bolts auyorizacion be tightened after aligning the seating surface, square to the lathe axis.